Wists, top web picks from pinkbird for all. Wists, social shopping scrapbook, wishlist

	about us \| help \| login » \| signup »

widgets Browse: latest picks
	Wists network: Cribcandy Popgloss Oobject Yokiddo

pinkbird's tags: show »

pinkbird is following: show »

Viewing: pinkbird/all (58 bookmarks) [ options:

rss or

publish on my site or

add to friends & faves ]

added on 2009-05-22

halter gown Â« weekend designer...

added on 2009-05-22

carbon couture: your cheat sheet to everythin...

The coffee paper filter flowers didn't work out. Maybe these will turn out better. added on 2009-05-22

calamity kim: how to make chiffon flowers by ...

added on 2009-05-22

my tiny sweet cheeks: tutorial tuesday: super...

japanese wallet tutorial...

added on 2009-05-15

amigurumi kawaii cupcake bear, with a cherry ...

added on 2009-05-15

beer can bracelets - now with (very image hea...

glass picture marble bracelet...

added on 2009-05-15

what to do with all those scraps?...

added on 2009-05-15

fork bracelet...

added on 2009-05-15

coin ring - how to...

added on 2009-05-15

jewelry valet...

added on 2009-05-15

pirate coin tutorial...

added on 2009-05-15

soldered flower tutorial...

added on 2009-05-15

soda can tab bracelet...

added on 2009-05-15

planetjune Â» shrink plastic ring t...

added on 2009-05-15

jewelry tutorial 019: double hook clasp - eni...

added on 2009-05-15

stamped id bracelet...

2008 diy winners: 4th place

i’m thrilled to announce our first diy contest winner of the day. fourth place, and a hearty congratulations, goes to angie johnson and her george nelson inspired jewelry case! angie was inspired by this classic george nelson piece and created an affordable diy version that was a crowd favorite from the beginning. i’m so honored to have her project on the site and to share the full instructions below.

julie will be receiving a $100 prize to put towards future diy projects (or anything else she wants) so please join me in congratulating angie on her hard work. thank you to angie for entering and for sharing this fantastic project. click here to view the full instructions for angie’s project or click “read more below”.

Angie’s George Nelson Inspired Jewelry Case

Supplies:
“Fira” chests from IKEA - 3 sets
“Fornbro” side table from IKEA
Sanding sponge - fine grit
Cotton rags
Rubber gloves
Stain in your choice of colour
Spray varnish - 6 cans
Handle for spray can (to make spraying easier, although this is not necessary)
Wrapping paper (although wallpaper scraps could be used as well)
Felt
White craft glue
“No More Nails” or similar adhesive
Small wood screws

Instructions:
1) Assemble the Fira chests, as per the included IKEA instructions (try to actually read them, I know it’s tempting with IKEA stuff to just go for the gusto and figure it out, but really, read them)

2) Lightly sand the chests, taking care to smooth off the edges. This is not the best quality wood, so these early prep stages are important to do properly. It can make the difference between a nice smooth finish, or a dull unprofessional look

3) Stain the chest (2 coats of stain) using a rag instead of a brush. Wipe on the varnish with one rag, then wipe off the excess with a clean rag. I suggest you have a lot of rags handy, and I HIGHLY suggest you wear rubber gloves, unless you think you would enjoy people staring at your hands for the next week or so.

4) After staining, give the chests a light sanding, and wipe away dust with a large dry paintbrush or clean dry cloth.

5) Now for the varnishing. I used a spray varnish to get a nice even coat. Slow and steady wins the race with this project. I also got a plastic handle that attaches to the spray can which makes spraying easier and gives your finger a break too. Make sure to do this in a well ventilated area, and wear a mask if possible. In total I gave this project about 8 coats of varnish with some light sanding after the second and sixth coats. I found I was getting a little obsessive about the smoothness of the finish and probably could have done about 4 more coats, but in the end I got tired of continually going to the hardware store for more varnish and decided to stop at 8.

6) After everything was dry and ready to go I lined the inside of the drawers in vintage wrapping paper. I measured and cut the paper to size, then glued it in with some watered down white craft glue and an old paintbrush. I also used the end of the paintbrush to smooth out the paper as I went. These methods helps avoid bubbles and lumps.

7) I then covered the inside bottom of the drawers with cream coloured felt. I didn’t glue it down in case I wanted to change the colour some day. As long as it fits snugly, it isn’t going anywhere.

8) I needed some way to keep all the earrings and necklaces untangled, so the tiny metal tins with glass lids from Lee Valley Tools were perfect. They come in many different sizes and are surprisingly affordable. The added benefit is that you can easily see all your jewelry through the glass lids. And the tins are really cute.

9) I attached the “Fornbro” table base to one of the chests with simple screws (making sure they are only the depth of the thickness of the wood) as well as some “No More Nails” glue for extra security.

10) Lastly I attached the 3 drawer sections to each other with a zig zag of heavy duty glue in the centers of the sections to be glued together. I used “No More Nails” but I think a lot of other types of thick glue would work.

The one revision I may make to this piece is to take the unused tabletop of the “Fornbro” table and attach it to the bottom of the legs. Essentially I will be using the side table upside down at this point. I find the chest is pretty stable right now (ie. it won’t fall over on its own), but this would make it even more stable when I’m late in the morning and am crazily pulling out drawers looking for something. If this is the case, I will paint the entire base white, since the table top is currently black.

I think that’s it, let me know if I’ve left out any details or if you need more info. I attached a couple pics my friend Mike (from Furni) took of my while I was doing the spray varnishing. Kind of funny, but people need to wear a mask and work in a ventilated area! added on 2009-05-15

design*sponge Â» blog archive Â...

added on 2009-05-15

wire wrapped ring tutorial...